Vanguard News

Balance, rotate, inflation, trade and longevity of tyres

Did you know that at 60km/h the sole contact between the road and your car is a small patch on your tyres about the size of your palm? As the only part of your car that  touches the road, it’s imperative your tyres are in good shape.

Derek Kirkby, Training Director at Ford’s Driving Skills for Life (DSFL), a programme which aims to promote  safe  driving culture, stated that tyres in good shape ensure  safer journey and even increase fuel efficiency. “If you are just 0.3 BAR below the optimum tyre pressure, you increase the rolling resistance of your vehicle by up to 10 per cent,”  adding that “optimum tyre pressure can provide up to three per cent better fuel economy. It all adds up!”

The following are four easy to remember tips from  Ford Motor Company and DSFL  on how to be more ‘road smart’ with  your tyres

BRIT: Balance, Rotation, Inflation, Tread

Balance: If your tyres and wheel assembly aren’t balanced, you’ll get an uncomfortable ride as  the steering wheel will vibrate and you could  damage  your tyres and your suspension. If you have a bumpy ride or you suspect that something may be wrong with your suspension, make sure  your technician checks your wheels for  balance.

 Rotation: Tyre rotation  involves moving tyres front to back and not left to right as most tyres are directional.  To ensure your tyres wear evenly and last longer, ensure that they’re rotated by a tyre expert at regular intervals as indicated by the vehicle or tyre manufacturer. Potholes can cause misalignment, which causes uneven tyre wear.

Inflation: You should have your tyres, including your spare  checked each time you stop at the filling station or at least weekly and preferably first thing in the morning when your tyres are cold. The optimum inflation pressure can be found on a sticker located inside the driver’s door. Don’t exceed the optimum pressure, because over-inflating tyres reduces their performance in terms of both traction and lifespan. Tyres with low pressure wear more quickly, degrade your vehicle’s handling, lower your vehicle’s load-carrying ability and increases fuel consumption.

Tread: Most tyres have a tread depth indicator and once the tyre is worn to that point, it needs to be replaced. To a degree, the tread on your tyres increases their grip on the road, deflects water and reduces slippage.

How to change a tyre

 Punctures happen  and  at the worst times. Follow these 10 steps and you’ll be back on the road in no time. Just remember, spare tyres aren’t designed for long distances or high speed, so once you  replace  a punctured tyre, you need to visit a tyre technician to fix or replace the original tyre as soon as possible.

*Pull over as soon as it is safe to do so, preferably on level ground.

*Turn on the hazard lights and  use the parking brake. Switch off the engine and place the reflective triangle on the road 45m behind your vehicle.

*Take out the spare tyre, jack and wrench. In most passenger vehicles, spare tyres are located under the floor of your boot, but  in SUVs and 4x4s, spares can also be on the rear, side, roof or underbody mounted.

*Remove the hubcap of the tyre that needs to be replaced and loosen the lug nuts with the wrench, turning counter-clockwise. Use your  weight on the wrench if you need to.

*Place the jack beneath your vehicle next to the tyre, and use the jack to raise your vehicle until the tyre is about 15cm above the ground, then remove the loosened nuts by hand.

*Carefully pull the flat tyre towards you until it is off the bolts. Set it down on its side so it doesn’t roll away.

*Mount the spare tyre on the exposed bolts and replace the nuts, tightening them by hand.

*Use the jack to lower your vehicle until the tyre is resting on the ground, and tighten the nuts with the wrench as much as you can.

*Lower the vehicle completely to the ground, and remove the jack.

*Stow your flat tyre, jack, and wrench, and continue your journey.

 

Latest News

Top Stories

Trending